What Size Water Pipe for a 5 Bathroom House at 200 Feet?
Engineering factsheet calculating water supply service line sizing for a 5 Bathroom Luxury Residence with a 200-foot municipal or well water run. Built to International Plumbing Code (IPC) and Uniform Plumbing Code (UPC) flow velocity criteria.
Material Engineering Comparison: PEX vs Copper vs CPVC
Flow dynamics at 29.5 GPM peak demand over 200 feet.
| Piping Material | Recommended Size | Inner Diameter (ID) | Flow Velocity | Friction Loss (200ft) | Remaining Pressure | Code Status |
|---|---|---|---|---|---|---|
| PEX SDR-9 (ASTM F876) | 1-1/2" PEX | 0.671 in | 7.8 fps | -35.8 PSI | ~25 PSI | Approved (≤ 8 fps) |
| Type L Copper (ASTM B88) | 1-1/4" Type L Copper | 0.785 in | 7.5 fps | -37.5 PSI | ~22.5 PSI | Approved (≤ 8 fps) |
| CPVC CTS (ASTM D2846) | 1-1/2" CPVC CTS | 0.677 in | 7.8 fps | -35.8 PSI | ~25 PSI | Approved (≤ 8 fps) |
Recommended Interior Branch Distribution Manifold
Dedicated feeder line to tank or tankless heater
Feeds dual vanities, freestanding tub & shower
Feeds guest bathrooms or powder room
Feeds kitchen sink, dishwasher & refrigerator line
Dedicated frost-free sillcock feed for max pressure
Standard terminal connection to angle stops & fixtures
Typical Fixture Inventory for 5 Bathroom Luxury Residence
IPC Table E103.3(2) WSFU WeightsNeed a Custom Fixture Count or Pressure Sizing?
Launch our full Water Supply Pipe Sizing Calculator to fine-tune flushometer valves, 2-story elevation head losses, and specific water meter sizes.
Frequently Asked Questions: 5 Bath Water Sizing
What size water main is required for a 5 bathroom home at 200 feet?
Under IPC Table E103.3 and standard residential plumbing codes, a 5 bathroom home has an aggregated load of 52 WSFU (~29.5 GPM peak demand). For a 200-foot run, the recommended water service line is 1-1/2" PEX or 1-1/4" Type L Copper. This maintains water velocity below the critical 8.0 feet/second threshold to eliminate pipe erosion and water hammer knocking.
Why can Copper sometimes use a smaller trade size than PEX for 5 baths?
Copper tubing (Type L ASTM B88) has significantly thinner walls than SDR-9 PEX tubing (ASTM F876). For example, 3/4" Type L Copper has an inside diameter of 0.785 inches, whereas 3/4" PEX is only 0.671 inches. Furthermore, PEX insert crimp fittings reduce flow area by up to 25%. On longer runs (200 ft), this friction difference frequently requires PEX to upsize to 1" where 3/4" Copper provides adequate volume.
How much water pressure is lost over a 200-foot service line?
At peak flow of 29.5 GPM, friction through 1-1/2" PEX creates approximately 4.5 to 8.5 PSI of dynamic head loss over 200 feet. If the residence is elevated on a second floor (+15 ft), add an additional 6.5 PSI of hydrostatic static head loss (0.433 PSI/ft). A street pressure of 55–65 PSI ensures comfortable terminal shower pressure.
What size water meter should be specified with this service line?
For a peak demand of 29.5 GPM in a 5 bathroom home, a 3/4-inch utility water meter is standard (rated for continuous flow up to 15 GPM and 25 GPM peak). For 4+ bathroom homes exceeding 25 GPM, municipal utilities mandate upgrading to a full 1-inch water meter.